1. Win32_10060 Anydesk Install
2. Win32 Error Code 10060 Anydesk

A Firebird Win32 Error 10060 error code 'anydesk' 'could Not Connect' immediately follow a previous improper shutdown and recent virus or malware infection recovery. Manufacturers and developers of software apps and hardware drivers is Win32 10060 error message? TCP-Ports 80, 443 and 6568. Windows Firewall request to allow the TCP-Listening Port on first session request. Windows Firewall If the TCP-Listening Port is enabled on AnyDesk clients that are not yet installed hence run portable, the Windows Firewall will asked for permission on the first session request. Disable the TCP.

Win32_10060 Anydesk Install

1. The anydesk is showing that the connection is an illegitimate connection in the user end. I am sure the cause was not due to firewall, restriction. How do I fix this issue, any suggestion is welcome.
2. Thanks for contributing an answer to Stack Overflow! Please be sure to answer the question.Provide details and share your research! Asking for help, clarification,.

This article provides help to fix Winsock timeout errors that occur on slow, congested, or high latency Internet links with Microsoft Proxy Server or ISA Server.

Original product version: Windows 10 - all editions
Original KB number: 191143

Symptoms

Winsock timeout errors may occur on slow, congested, or high latency Internet links with Microsoft Proxy Server or ISA Server. The following Winsock error Message appears on the client Web browser:

Proxy Reports:
10060 Connection timed out

The Web server specified in your URL could not be contacted. Please check your URL or try your request again.

Note

A timeout error may also occur when connecting to an Internet server that does not exist or if there is more than one default gateway on the Proxy Server computer.

Resolution

Important

This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see How to back up and restore the registry in Windows.

Adjusting the following TCP/IP setting by adding a subkey in the registry should reduce the number of timeouts by allowing more time for the connection to complete. This setting is not present in the registry by default.

1. Start Registry Editor (Regedt32.exe) and go to the following subkey:
   HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesTcpipParameters

2. On the Edit menu, click Add Value, and then add the following information:

   • Value name: TcpMaxDataRetransmissions
   • Value type: REG_DWORD - Number
   • Valid range: 0 - 0xFFFFFFFF
   • Default value: 5 Decimal
   • New value: 10 Decimal

3. Click OK, and then quit Registry Editor.

4. Reboot after registry change has been made.

More information

The TcpMaxDataRetransmissions parameter controls the number of times TCP retransmits an individual data segment (non-connect segment) before ending the connection. The retransmission timeout is doubled with each successive retransmission on a connection. It is reset when responses resume. The base timeout value is dynamically determined by the measured round-trip time on the connection.

The default value for this registry entry is 5; double this value to 10 (Decimal) (see step 2 above). If connection timeouts still occur, try doubling the value again to 20 (Decimal).

Note

This registry entry may only reduce the number of connection timeout errors that occur. Changes to your Internet connection or router may have to be made to completely resolve the problem.

The command line provides a tool to automate AnyDesk using scripts. For some cases AnyDesk uses the pipe mechanism of the operating system instead of parameters for higher security.

See also: Exit Codes, Automatic Deployment

Automatic Execution (script)

AnyDesk can be installed by script with the following command:

anydesk.exe --install <location> --start-with-win

Important:

<location> must be a valid installation path, e.g. c:anydesk. Currently, AnyDesk must be startedwith Windows.

For more installation parameters, see Automatic Deployment.

Initialization Parameters

Get Alias, ID, Status or Version

AnyDesk writes requested information to stdout.If the service is not running, SERVICE_NOT_RUNNING is returned and an exit is set indicating the error. If AnyDesk is not installed, it needs to be started first, in order to launch a local service.

On Linux, get AnyDesk Alias or ID of the installed and running AnyDesk, with this syntax:

anydesk --get-alias

Win32 Error Code 10060 Anydesk

anydesk --get-id

anydesk --get-status

anydesk --version

Use batch scripts for Windows:

to get ID:

to get Alias:

to get status:

to get version:

Setting a Password

For security reasons, a password for unattended access can not be set from the command line directly as this would enable malicious users to spy the password from the command line in Task Manager. Instead, a pipe is used to set the password.

echo password | anydesk.exe --set-password

Examples:

Standard client: echo my_new_password | anydesk.exe --set-password

Custom client: echo my_new_password | anydesk-123abc456.exe --set-password

This requires administrator privileges.

Removing the Password (for Windows only)

A non-preset unattended access password can also be removed from the AnyDesk client using the command line.

Examples:

Standard client: anydesk.exe --remove-password

Custom client: anydesk-123abc456.exe --remove-password

This requires administrator privileges.

Registering License Key

You can register a license with the current AnyDesk installation using the command line. The service must be running.

echo license_keyABC | anydesk.exe --register-license

Almost every scripting language has a pipe interface for stdin and stdout. See the programming language documentation for more information.

Connection Parameters

To connect to a remote AnyDesk ID or Alias, the syntax is: anydesk.exe alias@ad

The following commands can be added after the destination address (for Windows only):

Connecting with Password (for Windows only)

Example script that connects to alias@ad with password.Use command line or batch script:

echo password | 'C:Program Files (x86)AnyDeskAnyDesk.exe' alias@ad --with-password

Other Command Lines (for Windows only)

Open the Settings window:

To go to the specific setting page, the syntax is:

To open global settings: